Vanwell Oil Equipment(tianjin)Co.,Ltd.

中文  |  English

Vanwell Oil Equipment(tianjin)Co.,Ltd.
/
/
How to do a good job in the management and maintenance of oil drilling machinery and equipment

How to do a good job in the management and maintenance of oil drilling machinery and equipment

Equipment maintenance is one of the main contents of equipment management. If the equipment maintenance work is not done in daily production work, it will not only cause frequent equipment failures, but also have a great impact on production and personnel safety. With the continuous acceleration of the production speed of modern enterprises, the importance of equipment management has been continuously highlighted, which has caused the modern enterprise equipment management to become a science, and the development speed is very fast. In the actual enterprise equipment management, Wanweier should choose the appropriate equipment maintenance mode according to the actual needs of the enterprise. Only this time can it lay a better foundation for the long-term development of the enterprise.
 
     1. Impact of traditional equipment maintenance mode on drilling equipment management
 
     The traditional equipment maintenance is to carry out repair work after the equipment fails, which will cause the scale of the failure to be higher and the frequency of the failure to occur, which greatly increases the overall maintenance cost of the equipment to a certain extent , Increasing the operating cost of the equipment.
 
     With the increasing demand for petroleum resources, the production tasks of China's oil companies are getting heavier and heavier for oil drilling plans. Because the traditional maintenance mode cannot provide regular maintenance for drilling equipment failures, the occurrence of failures will directly As a result of the termination of the entire drilling plan, this will have a very big impact on the overall production plan of the entire enterprise. The drilling plan in this area is delayed, then the drilling plan in other areas will also be delayed, which seriously hinders the normal operation of the enterprise. Production, disrupting the overall plan of enterprise development.
 
     2. Various tasks that should be carried out in the management of drilling equipment
 
     Wanweier's inspection of drilling equipment. This work should be accompanied by the entire operation cycle of the drilling equipment. Not only should there be a detailed and targeted equipment inspection plan, but also various inspection records should be filled in carefully after the inspection work is completed, which can be used as a future pre-maintenance of drilling equipment Basic data.
 
     3. Do well the maintenance work of drilling equipment
 
     Before repairing the equipment, Wan Weier should not go up and dismantle and unload, but through the phenomenon of the failure, first analyze the possible causes of the failure, and then focus on the maintenance of the suspicious parts. After disassembling, you should look for the reason while disassembling. After you find the reason, you should not continue disassembling. For the maintenance of simple machinery, it is suspected that direct repair is used. If you encounter a complicated machine, you should first find out the design drawings of the machine, and then compare the drawings to find the cause of the failure. In the process of disassembly and repair, you should also repair it side by side. Take a picture while taking pictures to prevent the phenomenon of not knowing how to install after maintenance.
 
     For the maintenance of the mechanical control part, you should first check whether the various sensors and relay devices are faulty, check whether the sensors have normal signal output, check whether the functions of the relay devices are intact, and if there is no problem, you should check the various control circuits Normal, to see if there is a phenomenon of disconnection and short circuit, if it should be handled in time, if it is intact, the central control system of the machine should be opened, first check whether the various interfaces are firmly connected, and then check whether the control circuit board is intact. There is no damage or ablation of the device. If everything is normal, it means that some components on the circuit board have been damaged. At this time, the board should be handed over to a special maintenance person for repair.
 
     4. The foundation of preventive maintenance work for drilling equipment
 
     The basis of preventive maintenance work is that Wanweier establishes a maintenance standard for each type of equipment according to the specific characteristics of each equipment, and uses the established maintenance work standards to formulate a preventive maintenance plan for the equipment. During the maintenance of the entire drilling equipment, five types of maintenance standards should be established: operation, inspection, maintenance, and management. These 5 types of equipment maintenance standards should be run through the entire operation cycle of the equipment, and use it to carry out specific maintenance work on the equipment.